SpeakerTalk Forum Index SpeakerTalk
This forum has been set up to facilitate discussion of 1970s KEF speakers and drive units. The owner of the Forum has no connection with KEF Audio.
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

KEF 105.1 Refurbishment

 
Post new topic   Reply to topic    SpeakerTalk Forum Index -> KEF Speakers from the 1970s
View previous topic :: View next topic  
Author Message
LWCM
Introductory Contributor


Joined: 04 Oct 2018
Posts: 7

PostPosted: Wed Nov 28, 2018 4:25 am    Post subject: KEF 105.1 Refurbishment Reply with quote

Finally managed to sort out my "new" 105.1

Ordered the capacitors from Falcon Acoustics and managed to find a pair of T52. I wasnt sure if the distortion from one tweeter was bacause of the caps or a faulty tweeter.

Dismatled the speakers and removed the crossovers to do the recaping.

[img]https://pix.sfly.com/Whd9nA[/img]
https://pix.sfly.com/Whd9nA

[img]https://pix.sfly.com/XyxZfO[/img]
https://pix.sfly.com/XyxZfO

I then tried my best to sand down the cabinets to prepare for painting. This process was a pain as firstly the top of the bass cabinet had some glue and foam residue. Same for the plastic cover of the top cabinet. Secondly the wood was flaking at some parts of the top cabinet especially at areas where the metal grill covers are attached and also at the "window" of the Led lights. Every time I sand it, it flakes more. In the end I applied some super glue to prevent more flaking.

[img]https://pix.sfly.com/meNmOe[/img]
https://pix.sfly.com/meNmOe

[img]https://pix.sfly.com/6o6b-p[/img]
https://pix.sfly.com/6o6b-p

Next was the painting. I used a matt black paint. For the front cover of the bass cabinet I used a gloss laquer and for the rest of the cabinets I used a satin lacquer.

[img]https://pix.sfly.com/3XvhHB[/img]
https://pix.sfly.com/3XvhHB

[img]https://pix.sfly.com/JjE0cS[/img]
https://pix.sfly.com/JjE0cS

Next I also changed the Led lights as one was not working. Fixed back the crossovers and reassembled the cabinets and drivers.

Final results.

[img]https://pix.sfly.com/Xt7SXW[/img]
https://pix.sfly.com/Xt7SXW

Those portions which has flaked off previously I couldn't restore it to original condition so there are some indentations here and there on the top cabinet. I was told I needed to apply epoxy and slowly sand them? Well I was too tired after working on it for a week everyday after work. Maybe another time hahaha.

One thing I need some advice on. After recapping, I have the impression I lost some bass. I only played the speakers for a short while before working it as there was a distortion on one tweeter. But I thought I recalled the bass was stronger then. Any ideas?

Oh, the distortion was gone after the recap so I now have a pair of spare T52 Very Happy

*Somehow I cant attach the pics even when using [img][address][/img] method.
Back to top
View user's profile Send private message
audiolabtower
VIP Contributor 500+


Joined: 06 Jan 2009
Posts: 587

PostPosted: Wed Nov 28, 2018 3:37 pm    Post subject: Reply with quote

Excellent looking job, always nice to see classic speakers of that age looking good as new. Are the bass cabinets well sealed? Unpowered, pushing the coil of the B300 in gently by hand they should take about 5 seconds to slowly return to centre.
Back to top
View user's profile Send private message
LWCM
Introductory Contributor


Joined: 04 Oct 2018
Posts: 7

PostPosted: Wed Nov 28, 2018 6:02 pm    Post subject: Reply with quote

audiolabtower wrote:
Excellent looking job, always nice to see classic speakers of that age looking good as new. Are the bass cabinets well sealed? Unpowered, pushing the coil of the B300 in gently by hand they should take about 5 seconds to slowly return to centre.


It doesn’t seems air tight using this test.
Back to top
View user's profile Send private message
audiolabtower
VIP Contributor 500+


Joined: 06 Jan 2009
Posts: 587

PostPosted: Wed Nov 28, 2018 11:59 pm    Post subject: Reply with quote

That might explain any bass difference? Check the baffle sealing foam strip, B300 sealing gasket, internal edges, speaker cable tube glueing, binding post mounting tightness etc etc?
Back to top
View user's profile Send private message
LWCM
Introductory Contributor


Joined: 04 Oct 2018
Posts: 7

PostPosted: Thu Nov 29, 2018 1:46 am    Post subject: Reply with quote

audiolabtower wrote:
That might explain any bass difference? Check the baffle sealing foam strip, B300 sealing gasket, internal edges, speaker cable tube glueing, binding post mounting tightness etc etc?


Where can I get the sealing gaskets for the woofer? Anything I can use to replace?
Back to top
View user's profile Send private message
audiolabtower
VIP Contributor 500+


Joined: 06 Jan 2009
Posts: 587

PostPosted: Thu Nov 29, 2018 5:15 pm    Post subject: Reply with quote

Try 12in gaskets, or more easily I guess those windows sealing strips with the close cell foam.
Back to top
View user's profile Send private message
LWCM
Introductory Contributor


Joined: 04 Oct 2018
Posts: 7

PostPosted: Thu Nov 29, 2018 6:02 pm    Post subject: Reply with quote

Done. Used the foam tape meant for sealing windows and doors. Viola. Got my bass back
Back to top
View user's profile Send private message
audiolabtower
VIP Contributor 500+


Joined: 06 Jan 2009
Posts: 587

PostPosted: Thu Nov 29, 2018 6:11 pm    Post subject: Reply with quote

Excellent.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    SpeakerTalk Forum Index -> KEF Speakers from the 1970s All times are GMT + 1 Hour
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group